Nová verze firmware QuTS hero řady 5 je k dispozici v rámci aktualizace QuTS hero ve vaši NAS, nebo je možné FW stáhnout i v sekci "Centrum stahování".
Použitelné modely
- TS-h2490FU/TS-h1090FU
- TS-h1290FX
- TDS-h2489FU
- TS-h3088XU
- TVS-h1288X/TVS-h1688X
- TS-h987XU/TS-h987XU-RP/TS-h1887XU-RP/TS-h2287XU-RP/TS-h3087XU-RP
- TS-h1886XU-RP/TS-1886XU-RP/TS-1886XU-RP R2/TS-h1886XU-RP R2
- TS-h686/TS-h886
- TNS-h1083X
- TS-h1283XU-RP/TS-h1683XU-RP/TS-h2483XU-RP
- TS-h977XU-RP/TS-h1277XU-RP/TS-h1677XU-RP/TS-h2477XU-RP
- TVS-h1675U-RP/TVS-h1275U-RP/TVS-h875U-RP/TVS-h875U
- TVS-675
- TVS-h474/TVS-h674/TVS-h874
- TS-873AU/TS-873AU-RP/TS-1273AU-RP/TS-1673AU-RP/TS-873AeU/TS-873AeU-RP
- TS-h973AX/TS-473A/TS-673A/TS-873A
- TVS-672X/TVS-872X/TVS-672N/TVS-872N/TVS-472XT/TVS-672XT/TVS-872XT
- TS-1655
Storage&Snapshots
- To ensure the availability of your data, Storage & Snapshots now supports "Replace & Detach", which allows you to copy data from a faulty disk to a spare disk and then safely detach the faulty disk.
- Fixed the security issue CVE-2022-27600.
- Applied multiple security updates to further enhance system security.
- Fixed an issue where QuTS Hero might sometimes report abnormal fan speeds on the QM2 expansion card.
- Fixed an issue where users could not unlock an encrypted folder in File Station and the system might display an error message after a failed attempt.
- Fixed an issue where installing certain applications might occasionally cause Storage & Snapshots to keep refreshing shared folder statuses.
- Fixed an issue where users could not close the Quick Start wizard in Network & Virtual Switch if there had been another user whose username only differed in case sensitivity.
- Fixed an issue where security logs might repeatedly record the same events.
- Fixed an issue where File Station would display a preview window instead of directly downloading files when users tried to download files via a share link.
- Fixed an issue where the system generated dnsmasq logs whenever QVPN was connected or disconnected, causing insufficient space on the ram disk.
- Fixed an issue where the system could not mount a RDX QuikStor external drive that was formatted in ext4 and set to write-protection mode.
- Fixed an issue where the system would create a duplicate snapshot schedule if users clicked the "Apply" button twice when editing a snapshot schedule.
- Fixed an issue where users could not back up data for an exFAT external drive with HBS.
- Fixed an issue where the Overview section in Storage & Snapshots could not correctly display the status of SED drives.
- Fixed an issue where after entering the auto-protection mode, the NAS could not restart when the UPS resumed power. (Note: If a UPS is set up, the NAS can enter the auto-protection mode in the event of a power outage. Normally, the NAS will restart when the UPS resumes power.)
- Resolved an issue where the system could not send SNMP traps via a specified IP address after users created a VLAN connection.
- Fixed an issue where the NAS might occasionally shut down unexpectedly after users updated Container Station to 3.0.
- Users sometimes cannot switch between different FEC (Forward Error Correction) modes for the QXG-25G2SF-CX6LX network expansion card.
- SnapSync jobs for LUNs may fail after users edit LUN names.
- After users edit LUN settings and run a Snapshot Replica job, the destination NAS cannot correctly display LUN information in Snapshot Vault.
- Storage & Snapshots and iSCSI & Fibre Channel sometimes display different sizes of the same LUN after users revert a LUN by importing a snapshot.